LS3 Ported Head Comparisons

Posted by Ben Herndon on

Reference HotRod online, see link below for pictures and dyno charts

Loyal HRM readers will no doubt remember our "Ultimate Chevy LS Cylinder Head Test" in the Dec. '10 issue in which we tested 11 different LS1/LS6 cathedral-port-style heads. In this issue we're doing the same thing, but with LS3/L92 rectangular-port heads. Included are dedicated castings from Mast Motorsports and Procomp Motorsport, five different CNC-ported stock castings from various manufacturers, and a baseline test of stock LS3 heads. It should not be overlooked that our test motor produced nearly 700 hp with those OE, as-cast cylinder heads.

Along with a significant amount of airflow and power data, this test features controversy, destruction, and one seriously stout test mule. We built a 468ci stroker to match the monster flow offered by the heads being tested, and credit must be given to Darton Machinery, Wiseco Pistons, and K1 Technologies for their support of this project. Darton machined the factory block and installed its ultrabeefy Modular Integrated Deck (MID) kit that allowed us to safely combine a set of 4.185-inch Wiseco forged pistons with a 4.250-inch stroker crank from K1 to produce 468 ci of displacement. We had a static compression ratio of 12.2:1 and a custom Comp Cams hydraulic roller with 255/271 degrees of duration at 0.050, 0.624 lift, and a 115-degree lobe-separation angle. The reason for the wide split between intake and exhaust duration is that the rectangular-port heads feature a relatively poor intake-to-exhaust-flow relationship as a result of impressive intake flow (always desirable) but lackluster exhaust flow (not so much).

We ran all our tests using a single-plane intake from Mast Motorsports and also checked one of the combinations with the FAST LSXR LS3 intake and 102mm throttle-body to illustrate the difference in power between the carbureted and injected combos. The Mast intake is a work of art and would be a welcome addition to any race motor. It would not fit under the hood of any production car we know of, but it sure looked cool topped off by the 1,050-cfm Holley Ultra Dominator carburetor. Even during carbureted testing, a FAST system provided the timing curve. All combinations were run with American Racing 17/8-inch headers feeding 18-inch collector extensions (no mufflers). Jetting and timing were adjusted for each setup, but every combination produced best power with 28 degrees of total timing. All the heads were run with stock LS3 rockers with one exception: The 12-degree, large-bore Mast heads required 1.8:1 LS7 rockers. This increased lift from 0.624 to 0.660. That obviously added power, but the Mast heads also offered the highest airflow, so let the controversy begin.

Each combination was run from 3,500 rpm to 7,000 rpm. Regardless of the heads installed, the engine always made peak power below 7,000 rpm. For every test, we've reported not just the peaks but also the average horsepower and torque from 3,500 to 6,700 rpm along with the torque reading at 4,000 rpm (an indication of low-speed performance).

  • To achieve the desired displacement, we shipped a production aluminum block to Darton for
  • The machining from Darton included stroker-clearancing the bottom of the liners. Additiona
  • The machined block was stuffed with a custom stroker kit from Wiseco that featured a forge

Every head was also checked on the flow bench, and the combustion chamber and intake port volumes were measured. The manufacturers supplied their heads with 70cc chambers (our measurement only verified that we had no high-compression ringers) and sufficient spring pressure for our cam and rpm potential.

See the results yourself (each dyno graph compares the head tested with the stock LS3 heads), but except the Mast 12-degree heads, the difference in average power among all the (1.7 rocker) LS3-based combinations was insignificant. We look at the data in terms of peak and average numbers, but the reality is that 1 or 2 hp is irrelevant when the motor makes more than 700 hp. Any of these LS3 heads (including the stock castings) are capable of serious power. Owning an LS3-headed motor has never been better.

  • Massaging of the Milodon windage tray was necessary to clear the stroker crank. Note the u
  • The Darton MID modifications and 4.185 bore diameter required dedicated head gaskets. The
  • Comp Cams supplied the hydraulic roller cam and double-roller timing chain. The LSR cam sp
  • Not wanting to restrict the power potential of the LS3 heads, we installed this trick sing
  • Prior to running, every head was tested on the flow bench from 0.050- to 0.700-inch lift.
  • Our testing was not without incident, as the factory damper snapped off at 7,000 rpm and b

Test 1
Stock LS3/L92 (0821 casting)

Retail price: $899 (plus the valvesprings of your choice)
Intake valve size: 2.165
Exhaust valve size: 1.59
Intake port volume: 260 cc
Exhaust port volume: 90 cc
Chamber volume: 70 cc
Peak power: 692 hp at 6,500 rpm
Peak torque: 625 lb-ft at 4,900 rpm
Average horsepower (3,500-6,700): 567.7 hp
Average torque (3,500-6,700): 583.1 lb-ft
Torque at 4,000 rpm: 557.5 lb-ft

FLOW DATA: CFM AT 28 INCHES
LIFT INTAKE EXHAUST
0.050 34 24
0.100 67 59
0.200 147 116
0.300 211 157
0.400 259 188
0.500 297 207
0.600 312 216
0.650 312 219
0.700 314 223

Our baseline test used stock, as-cast heads that we removed from an LS3 crate engine, though these heads are also available from GM Performance Parts, and they are the most affordable heads we tested. Though considerably down in flow compared with the aftermarket heads, the flow is a significant step up from either traditional small-block or even the earlier LS1 castings with a peak intake flow of 314 cfm. The valvespring combination on the stock LS3/L92 heads was never designed to accept a 0.624-lift cam, so we replaced the stock springs with a set of PN 26918 springs and retainers from Comp Cams. That's all that's required to fit this camshaft; no guide machining was required.

Test 2
GMPP CNC (5364 Casting)

Retail price: $1,495
Intake valve size: 2.165
Exhaust valve size: 1.59
Intake port volume: 279 cc
Exhaust port volume: 95 cc
Chamber volume: 70 cc
Peak power: 720 hp at 6,500 rpm
Peak torque: 629 lb-ft at 4,800 rpm
Average horsepower (3,500-6,700): 578.7 hp
Average torque (3,500-6,700): 593.4 lb-ft
Torque at 4,000 rpm: 558.0 lb-ft

FLOW DATA: CFM AT 28 INCHES
LIFT INTAKE EXHAUST
0.050 34 26
0.100 71 61
0.200 150 110
0.300 226 154
0.400 273 184
0.500 313 206
0.600 341 219
0.650 349 222
0.700 354 226

Who better to port the factory LS3/L92 heads than GM, or more specifically, GM Performance Parts? With full CNC porting, the GMPP PN 88958698 LS3 heads offered impressive intake flow numbers, registering 354 cfm at 0.700 lift. As we have come to expect of the LS3/L92 heads, the exhaust flow lagged behind the intake significantly at 226 cfm. The ported LS3/L92 heads featured sizable intake port volumes of 279 cc; while not much of an issue on our 468ci stroker, that might be a tad large for a small-displacement LS. The power output of the 468 jumped from 692 hp at 6,500 rpm with stock L92 heads to 720 hp at 6,700 rpm with the CNC-ported versions. The peak torque was up slightly, from 625 lb-ft at 4,900 rpm to 629 lb-ft at 6,900 rpm. The power gains were evident as low as 4,300 rpm, but the major gains came past 5,000 rpm. The ported heads were obviously worth additional power, but other than the LS7, what factory head can produce nearly 700 hp in stock trim?

Test 3
SDPC CNC LS3/L92 (0821 Casting)

Retail price: $1,529
Intake valve size: 2.165
Exhaust valve size: 1.59
Intake port volume: 280 cc
Exhaust port volume: 94 cc
Chamber volume: 70 cc
Peak power: 723 hp at 6,800 rpm
Peak torque: 635 lb-ft at 4,900 rpm
Average horsepower (3,500-6,700): 582.2 hp
Average torque (3,500-6,700): 597.3 lb-ft
Torque at 4,000 rpm: 567.4 lb-ft

FLOW DATA: CFM AT 28 INCHES
LIFT INTAKE EXHAUST
0.050 33 25
0.100 67 54
0.200 143 112
0.300 209 163
0.400 262 201
0.500 309 227
0.600 349 239
0.650 357 245
0.700 358 248

Though a GM Performance Parts dealer, Scoggin-Dickey Performance Center offers its own CNC-ported heads, and they offered slightly more performance than the GMPP heads. Compared with the GMPP castings, the SDPC heads had more high-lift and peak intake flow but traded the high-lift for mid-lift flow. The SDPC exhaust side bettered the GMPP counterparts by as much as 23 cfm. Average power for the SDPC heads was 3.5 hp and 3.9 lb-ft ahead of the GM versions. The SDPC heads offered sizable power gains over the stock heads from 3,500 rpm through 6,700 rpm. The heads we used were PN SD5882-1 with stock LS3 valves and with springs set up for 0.660-inch lift.

Test 4
LPE CNC (823 Castings)

Retail price: $1,699.95
Intake valve size: 2.165
Exhaust valve size: 1.59
Intake port volume: 271 cc
Exhaust port volume: 93 cc
Chamber volume: 70 cc
Peak power: 718.7 hp at 6,800 rpm
Peak torque: 627.7 lb-ft at 4,800 rpm
Average horsepower (3,500-6,700): 576.7 hp
Average torque (3,500-6,700): 591.8 lb-ft
Torque at 4,000 rpm: 561.2 lb-ft

FLOW DATA: CFM AT 28 INCHES
Lift INTAKE EXHAUST
0.050 34 24
0.100 67 54
0.200 141 112
0.300 207 173
0.400 261 217
0.500 303 238
0.600 341 248
0.650 355 252
0.700 360 254

When you think of LS performance, it is hard not to think of the name Lingenfelter. The commitment to quality and performance started by the late John Lingenfelter continues to this day. The company starts with OE heads, CNC ports them, and completes them with 2.165/1.59 valves, 271/93cc intake/exhaust port volumes, and the specified 70cc combustion chambers. The work paid off, as the 468 produced 717 hp at 6,800 rpm and 627 lb-ft at 4,800 rpm. The LPE CNC heads offered a nice torque gain from 4,300 rpm to 4,900 rpm then carried better power numbers above 5,200 rpm. The part number for these heads is LS#CNC-Complete.

Test 5
Mast Black Label LS3 (Large Bore)

Retail price: $3,198
Intake valve size: 2.20
Exhaust valve size: 1.60
Intake port volume: 270 cc
Exhaust port volume: 93 cc
Chamber volume: 70 cc
Peak power: 761 hp at 6,500 rpm
Peak torque: 645 lb-ft at 5,100 rpm
Average horsepower (3,500-6,700): 596.1 hp
Average torque (3,500-6,700): 609.1 lb-ft
Torque at 4,000 rpm: 557.3 lb-ft

FLOW DATA: CFM AT 28 INCHES
LIFT INTAKE EXHAUST
0.050 34 24
0.100 74 54
0.200 141 106
0.300 229 154
0.400 299 200
0.500 341 232
0.600 371 248
0.650 380 254
0.700 365 261

The Mast Black Label large-bore heads are for engines with bores of 4.125 inches and up, and our 468 had healthy 4.185 bores. The Mast heads differed from most of the heads in this test as they were dedicated castings rather than ported stockers. By designing a port that was not limited by production architecture, Mast exceeded the flow of any of the ported stockers. Power followed suit with peak numbers of 761 hp at 6,500 rpm and 645 lb-ft at 5,100 rpm. These heads had the highest average power as well. It should be noted that the Mast heads required use of 1.8:1 LS7 rocker arms and supplied billet rocker stands rather than the 1.7:1 LS3 rockers used on every other head tested. This increased the lift from 0.624 to 0.660. This was a power advantage, but the larger (heavier) valve combined with the increase in rocker ratio created a slight valve control issue.

Test 6
Dr. J's CNC LS3 (ProComp Motorsport Casting)

Retail price: $2,395
Intake valve size: 2.20
Exhaust valve size: 1.60
Intake port volume: 279 cc
Exhaust port volume: 94 cc
Chamber volume: 70 cc
Peak power: 730 hp at 6,900 rpm
Peak torque: 629 lb-ft at 4,800 rpm
Average horsepower (3,500-6,700): 580.7 hp
Average torque (3,500-6,700): 595.3 lb-ft
Torque at 4,000 rpm: 560.2 lb-ft

FLOW DATA: CFM AT 28 INCHES
LIFT INTAKE EXHAUST
0.050 34 26
0.100 65 54
0.200 141 118
0.300 211 163
0.400 270 196
0.500 321 225
0.600 357 239
0.650 374 243
0.700 359 246

Like the offerings from Mast Motorsports, the Dr. J's CNC LS3 heads were dedicated castings (from Procomp Motorsport). That the two non-OE castings offered the highest peak flow numbers of our test indicates that the factory heads, even in ported form, can certainly be improved upon. The Dr. J's CNC job on the Procomp Motorsport heads offered peak flow numbers of 374 cfm on the intake and 246 cfm on the exhaust using factory valve sizes. Like the Mast heads, the flow rate of the Dr. J's Procomp heads leveled off and dropped slightly after 0.650 lift (the range of 95 percent of street/strip cams). The peak of 730 hp at 6,900 rpm is the highest output of the LS3 heads equipped with 1.7:1 rockers. This is a perfect example of why we include average power numbers, as despite the big peak power number, the heads from Dr. J's finished behind SDPC and WCCH (albeit by just 1.5 hp and 2 lb-ft) with average power numbers of 580.7 hp and 595.3 lb-ft.

Test 7
TEA CNC LS3/L92 (823 Casting)

Retail price: $1,659
Intake valve size: 2.165
Exhaust valve size: 1.59
Intake port volume: 279cc
Exhaust port volume: 91 cc
Chamber volume: 70 cc
Peak power: 722 hp at 6,900 rpm
Peak torque: 631 lb-ft at 4,900 rpm
Average horsepower (3,500-6,700): 578.2 hp
Average torque (3,500-6,700): 593.1 lb-ft
Torque at 4,000 rpm: 560.7 lb-ft

FLOW DATA: CFM AT 28 INCHES
LIFT INTAKE EXHAUST
0.050 35 26
0.100 70 57
0.200 144 110
0.300 226 153
0.400 285 191
0.500 326 219
0.600 350 232
0.650 356 239
0.700 365 241

We have always had good luck with heads by Total Engine Airflow. The TEA Stage 2 LS3/L92 heads featured the requisite CNC porting, a 2.165/1.59 (factory) valve package and 70cc combustion chambers. As delivered from TEA, the LS3 heads offered peak intake flow numbers of 365 cfm, while the exhaust flow checked in at 241 cfm. These peak numbers were combined with impressive mid-lift flow numbers that led the field at 0.300 and 0.400 lift. In terms of peak numbers, the TEA-headed 468 produced 721 hp at 6,900 rpm and 631 lb-ft at 4,900 rpm. Torque production down at 4,000 rpm was an impressive 560.7 lb-ft, bettered only by the LPE and SDPC LS3 heads (not counting the Mast 12-degree Black Label heads with 1.8 rockers).

Test 8
West Coast Racing Cylinder Heads CNC LS3/L92

Retail price: $2,180
Intake valve size: 2.20
Exhaust valve size: 1.6
Intake port volume: 280 cc
Exhaust port volume: 97 cc
Chamber volume: 70 cc
Peak power: 726 hp at 6,600 rpm
Peak torque: 630 lb-ft at 4,900 rpm
Average horsepower (3,500-6,700): 581.6 hp
Average torque (3,500-6,700): 596.1 lb-ft
Torque at 4,000 rpm: 559.2 lb-ft

FLOW DATA: CFM AT 28 INCHES
Lift INTAKE EXHAUST
0.050 34 26
0.100 71 60
0.200 159 116
0.300 227 174
0.400 279 218
0.500 320 234
0.600 349 247
0.650 358 251
0.700 361 253

The West Coast Racing Cylinder Heads units arrived at the last minute on the final day of our testing. The company's CNC-ported LS3/L92 heads offered a couple of unique features, including 2.20-inch intake and 1.60-inch exhaust valves. Add 280cc intake and 97cc exhaust ports and you get some impressive flow rates: peak intake flow was 361 cfm at 0.700 lift with 253 cfm on the exhaust. Did these numbers generate decent power? How about 726 hp at 6,600 rpm and 630 lb-ft at 4,900 rpm (bettered only by the Mast and Dr. J's heads)? With the exception of the Mast heads, the power difference between all the ported production castings was just 13 hp. On a 720hp motor, 13 hp is not very significant, especially when you consider that the average power production varied by just 4 hp. These are all great heads, and even the stock LS3 casting offered impressive power.

Test 9
ProComp Motorsport CNC LS3

Retail price: $1,875
Intake valve size: 2.20
Exhaust valve size: 1.60
Intake port volume: 279 cc
Exhaust port volume: 94 cc
Chamber volume: 70 cc
Peak power: 718 hp at 6,900 rpm
Peak torque: 623 lb-ft at 4,900 rpm
Average horsepower (3,500-6,700): 570.7 hp
Average torque (3,500-6,700): 585.1 lb-ft
Torque at 4,000 rpm: 552.8 lb-ft

FLOW DATA: CFM AT 28 INCHES
LIFT INTAKE EXHAUST
0.050 34 26
0.100 62 53
0.200 140 116
0.300 206 161
0.400 260 194
0.500 317 225
0.600 350 232
0.650 358 238
0.700 350 244

Starting with dedicated castings, Procomp Motorsport was able to eliminate many of the problems associated with porting the factory castings. The Procomp heads had peak flow of 358 cfm on the intake and 244 cfm on the exhaust using 2.20/1.60 valves. Like with the Mast heads, the flow rate of the Procomp heads dropped slightly after 0.650 lift. According to Procomp, our flow bench numbers are down in flow by nearly 15 cfm compared with the company's data, but we will have to flow test another set to verify the numbers. These flow numbers produced peak power numbers of 718 hp at 6,900 rpm and 623 lb-ft at 4,800 rpm. The ported heads produced average power numbers of 570.7 hp and 585.1 lb-ft of torque.



Read more: http://www.hotrod.com/techarticles/engine/hrdp_1102_ls3_l92_rectangle_port_cylinder_heads_test/viewall.html#ixzz2JqldRFK9

Older Post Newer Post


620 comments

Created on Posted by HildaGAP Comment Link

Már több mint 17 millió koronavírus-fertőzöttet regisztráltak világszerte

Created on Posted by Denisemus Comment Link

MД°NECRAFT AMA YATAKLAR BД°ZE SALDIRIYOR 😱 – Minecraft

Created on Posted by Sarahdog Comment Link

നടപ്പാലമില്ലാതെ ബുദ്ധിമുട്ടി കാന്‍സര്‍രോഗിയും കുടുംബവും മനസലിയാതെ കൊല്ലം കോര്‍പ്പറേഷന്‍

Created on Posted by Joyceswern Comment Link

BB Ki Vines-Sameer Vs Hola – The Ultimate Roast

Created on Posted by Gracesinty Comment Link

Escape First Funny Moments – Brian Goes Crazy Over Triangles


Leave a comment

Scroll To Top